/**
*
 Marlin 3D Printer Firmware 

*
 Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]* 

*
 Based on Sprinter and grbl.

*
 Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* 


*
 This program is free software: you can redistribute it and/or modify

*
 it under the terms of the GNU General Public License as published by

*
 the Free Software Foundation, either version 3 of the License, or 

*
 (at your option) any later version.
* 


*
 This program is distributed in the hope that it will be useful,

*
 but WITHOUT ANY WARRANTY; without even the implied warranty of

*
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 

*
 GNU General Public License for more details.
 * 


*
 You should have received a copy of the GNU General Public License

*
 along with this program. If not, see <http://www.gnu.org/licenses/>.
*
 */ 



/*****************************************************************
* GT2560 V3.0 pin assignment*****************************************************************/ 
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools ->Boards' menu. #endif 
#ifndef BOARD_NAME #define BOARD_NAME "GT2560 V3.0" #endif 
//
// Servos
//
#define SERVO0_PIN 11 // 13 untested 3Dtouch 

//
// Limit Switches
//
#define X_MIN_PIN 24 //22
#define X_MAX_PIN 22 //24
#define Y_MIN_PIN 28 //26
#define Y_MAX_PIN 26 //28
#define Z_MIN_PIN 30 
#define Z_MAX_PIN 32 

#ifndef FIL_RUNOUT_PIN
 #define FIL_RUNOUT_PIN 66 #endif #ifndef FIL_RUNOUT2_PIN
 #define FIL_RUNOUT2_PIN 67 
#endif  
// Detect power-loss#define CONTINUITY_PIN  69  
#define CONTINUITY_STATE  HIGH  
//// Steppers//#define X_STEP_PIN  37  
#define X_DIR_PIN  39  
#define X_ENABLE_PIN  35  
#define Y_STEP_PIN  31  
#define Y_DIR_PIN  33  
#define Y_ENABLE_PIN  29  
#define Z_STEP_PIN  25  
#define Z_DIR_PIN  23  
#define Z_ENABLE_PIN  27  
#define E0_STEP_PIN  46  
#define E0_DIR_PIN  44  
#define E0_ENABLE_PIN  12  
#define E1_STEP_PIN  49  
#define E1_DIR_PIN  47  
#define E1_ENABLE_PIN  48  
//// Temperature Sensors//#define TEMP_0_PIN  11  
#define TEMP_1_PIN  9  
#define TEMP_2_PIN  -1  
#define TEMP_BED_PIN  10  
//// Heaters / Fans//#define HEATER_0_PIN  10  
#define HEATER_1_PIN  3  

//43//45//41 
// Analog Input (8)// Analog Input// Analog Input// Analog Input 
//2 
#define HEATER_2_PIN -1 
#define HEATER_BED_PIN  4  
#define FAN_PIN  9  
//// Misc. Functions//#define LED_PIN  6  
#define PS_ON_PIN  12  
#define KILL_PIN  -1  
#define SUICIDE_PIN  54  

start, to keep power flowing. 
#if ENABLED(LIGHT_SUPPORT)//#define LIGHT_SWITCH_PIN 21#define LIGHT_PIN 6 
#endif 

//
// SD
//
#define SDSS 53 
#define SD_DETECT_PIN 38 
#define SDPOWER -1 

//
// LCD / Controller
//
#define BEEPER_PIN 18 

#define LCD_PINS_RS 20 
#define LCD_PINS_ENABLE 17 
#define LCD_PINS_D4 16 
#define LCD_PINS_D5 21 
#define LCD_PINS_D6 5 
#define LCD_PINS_D7 36 

#if ENABLED(NEWPANEL)#define BTN_EN1 42 #define BTN_EN2 40 #define BTN_ENC 19 
#endif 
// PIN that has to be turned on right after